Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Gate Installation in Covina: What to Know First
We install, service, and repair Ghost Controls gate openers across Covina, and most jobs are completed in a single visit. As an independent Ghost Controls service provider, we work on the full range of their swing and slide gate systems, from the GTS and GSD series up through the newer Gen II and AXDP models. The price is always settled before we turn a single bolt, and every Ghost Controls installation we do carries our written 90-Day Done Right Promise.
If you have a Ghost Controls opener sitting in a box, or one that’s been fighting you for years, call (350) 238-6295. A live person answers, day or night.
Key Takeaways:
- Independent Ghost Controls gate installation for all Covina neighborhoods, from Charter Oak to Covina Hills
- Most Ghost Controls jobs finished in one visit
- Upfront pricing agreed before work starts
- 90-Day Done Right Promise in writing, on every job
- We service eight other gate opener brands, so if you ever switch, we’re still the call
How Ghost Controls Products Fail - and How We Fix Them
Ghost Controls makes a solid opener for the money, but like every brand, they have their patterns. Here are the failure modes we see most in Covina driveways, and what we do about them.
- AXDP series limit-switch drift: The AXDP and similar Gen II models use magnetic limit sensing, and after a few hundred open-and-close cycles the board can lose its reference point. The gate will stop short or over-travel and sit there buzzing. We recalibrate the limits and check the mount brackets, because a loose bracket will mimic the same symptom. If the sensor board itself is corroded, we replace it and reset the travel parameters from scratch.
- GTS series arm sag on double gates: On a double swing gate with a GTS opener on each leaf, the arm bushings wear unevenly. One side starts closing a half-second behind the other, and the homeowner hears a “clunk” as the second leaf slams. We shim or replace the bushings and re-time both operators so the leaves move in sequence, not against each other.
- GSD slide-gate chain stretch: Ghost Controls slide openers pull a chain, and Covina’s heat plus the dust that blows down from the foothills means chains stretch faster than the manual suggests. A stretched chain skips teeth on the drive sprocket, which sounds like a gearbox failure but almost never is. We tension, inspect the sprocket for wear, and replace the chain only when it’s actually done.
- Battery backup dead on arrival: A lot of Covina homeowners add the Ghost Controls battery backup kit, and we see units that were installed a year ago and never exercised. Lead-acid standby batteries sulfate when they sit. We load-test the battery, clean the terminals, and if it won’t hold a charge we explain the replacement cost before doing anything.
- Control board phantom activation: Occasionally a Ghost Controls board picks up stray RF from a neighbor’s opener or a nearby cell tower. The gate opens on its own, usually at 2 a.m. We re-pair the remotes, change the DIP or code settings, and if the board is glitching we replace it rather than leave a gate that might open itself at night.
Our Ghost Controls Gate Installation Process
Here’s how a typical Ghost Controls job goes from first call to final test.
- 1
Call and describe the symptom. We ask what the gate is doing, which Ghost Controls model you have, and whether it’s a swing or slide. That tells us which parts to bring.
- 2
On-site inspection. We check the opener, the gate itself, the hinges or rollers, and the power run. Half the time the “opener problem” is actually a sagging hinge or a tired wheel.
- 3
Written quote, agreed before work. We hand you a price for parts and labor. You approve it. Then we start.
- 4
The installation. We mount, wire, set limits, program remotes, and test the safety edges and photocells. On a Ghost Controls job we’re particular about the mount plate, because a flexing plate shortens the life of any arm or chain operator.
- 5
Full-cycle testing. We run the gate open and closed a dozen times, check force settings, and make sure the auto-close delay is set the way you want it.
- 6
Cleanup and the Promise. We leave the site clean, walk you through the remotes and the manual release, and you get the 90-Day Done Right Promise in writing. If anything’s off, we come back.
What Ghost Controls Gate Installation Costs in Covina
Straight numbers, because that’s how we do business.
- Single swing gate, Ghost Controls GTS kit install: $450-$750 typical, including mounting, wiring, and programming
- Double swing gate with paired GTS/Gen II operators: $900-$1,400 depending on gate weight and power access
- Sliding gate with GSD chain-drive: $800-$1,300 including chain sizing and safety-edge install
- Opener replacement, existing gate, like-for-like Ghost Controls swap: $380-$600
- Full new gate plus Ghost Controls automation: $2,200-$4,500 depending on material, size, and site prep
What moves the price: gate weight, whether power’s already at the post, the condition of the hinges or track, and whether you want accessories like a keypad, battery backup, or a vehicle sensor. We quote it before we start, and that’s the price you pay. Call (350) 238-6295 for an exact number. Estimates are free.
Why Covina Homeowners Call Ironworks Gate Co. for Ghost Controls Work
Victor Salinas grew up in Charter Oak, not far from Covina Park, and he’s still here. He learned the trade through Citrus College’s Industrial Technology program and years alongside working ironworkers, and he’s been fixing gates in this city for over 42 years. His father was a machinist who taught him one thing that stuck: metal doesn’t lie. A gate should open when you need it to and stay closed when you don’t. Everything else is just the work.
So when a Covina homeowner calls us about a Ghost Controls opener, they get a technician who knows that brand cold, and seven others besides. LiftMaster, Mighty Mule, DoorKing, FAAC, BFT, Linear, Viking, Elite – if it’s on a driveway in the San Gabriel Valley, we’ve worked on it. Most Ghost Controls jobs are done in one visit. Every job is backed by the 90-Day Done Right Promise. No paperwork, no arguing. If it’s not right, we come back and make it right. We’ve been here since 1984, and we plan to be here another forty years.
FAQs
No, as long as the parts meet Ghost Controls specifications. We use OEM Ghost Controls parts when they’re available and appropriate, and quality aftermarket equivalents when OEM lead times are unreasonable. We’ll tell you which is which and why before we order anything.
Often yes. Most Ghost Controls installations in Covina are done in a single visit, and if you call early enough we can usually get a technician to you that same day. Call (350) 238-6295 and a live person will tell you exactly when we can be there.
If the board is failing and the arm is worn, replacement usually makes more sense than repairing piecemeal – you’d spend near the cost of a new opener over the next two years. But if it’s a single component like a limit sensor or a stretched chain, repair is the better call. We’ll tell you straight which one applies to your gate, and the quote is free.
Yes. Every installation quote includes the electrical run from the panel or outlet to the operator, plus safety edges and photocells where the gate requires them. We don’t hand you a “motor only” price and then surprise you with wiring costs.
Call (350) 238-6295. Describe the symptom, tell us the model if you can find it on the opener arm or control box, and we’ll bring the right parts and get it handled.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Covina and nearby areas.